Specifications:
Monitor:
Screen Dimensions: 7 inch
Resolution: 480(W)x RGB x 234(H)=336960Pixels
System: PAL/NTSC
Power: DC12V
Consumption: 6W
Video: Tow way video input
Audio: One way audio input
Rear Watching: Image can be changed left and right
Operate Mode: The Key operation and remote control
Camera:
Image Sensor: Color CCD CMOS
TV System: PA / NTSC
Horizontal Resolution: 420 TVL
Effective Pixels: PAL: 512 x 582, NTSC: 512 x 492, OV7949: 628 x 586(PAL), PC 1030 PAL/NTSC: 640 x 480
Sensing Area: 1/3: 4.9mm x 3.7mm, 1/4: 3.6mm x 2.7mm, , OV7949: 5.961 x 4.276mm, PC 1030 PAL/NTSC: 3.5964 x 2.7084
Min. Illumination: 1.0 Lux/F1.2. (0 Lux whth IR on), 0.5 Lux(0 Lux with IR on)
Diagonal Viewing Angle: 120℃, 170℃ (optional)
Night Vision: 0, 3-5m, 5-10m, 10-15m (optional)
Video Output: RCA connector 1.0Vp-p.75ohm
Current Consumption: 50~60mA, Max 300mA with IR on
Power Supply: DC 12V
Operating Temperature: -20℃~60℃, RH95%MAX
Storage Temperature: -40℃~80℃, RH95%MAX
How to Install a Rearview Mirror Monitor in Your Car:
Disconnect the battery cables from the battery before beginning installation. Use a wrench or socket to remove the battery cables. Check the vehicle's repair guide for the proper wrench or socket size.
Remove the original rearview mirror from your car. Leave its mounting bracket on the windshield-you'll attach the rearview mirror monitor to this. Check the rearview mirror's mounting screw to see what size screwdriver you'll need
Insert the rearview mirror monitor into the existing mounting bracket on your windshield. Use the bolt supplied with the monitor to secure the device in the mounting bracket
Route an A/V power cable from the A/V selector box to the monitor. Connect the A/V cable from the monitor to the A/V power cable. Use cable ties to secure the cables and prevent them from hanging
Reconnect the battery. Start your vehicle and select the rearview mirror monitor on the A/V selector box. The video monitor should come on if the rearview mirror monitor is correctly installed
How to Install a Camera in Your Car:
Disconnect the battery cables from the battery. Check the vehicle's repair manual to find out what size wrench to use. Leave the disconnected cables a safe distance from the battery posts
Decide where you want to install the rear-view camera. Most people put them in the plastic bumper so they don't have to drill into the car's sheet metal
Drill a hole for the camera. Check the installation instructions to see what size drill bit to use. Don't make the hole too large or the camera will fall out
Place the camera in the hole using the rubber grommet supplied with the camera. Make sure the camera and grommet are tight
Attach the camera's power wire to the backup-light power wire on your car. You'll have to splice the wires together. Use wire cutters to cut the wires, leaving enough excess wire to reconnect. Strip the ends of the wire to expose the bare wire using wire strippers. Splice the wires together using a two-into-one connector. This will give the rear-view camera power when you put the car in reverse
Route the camera's output wire to the rear-view monitor and connect the wire to the monitor's input. For installation of the monitor, see the monitor's installation instructions
Reconnect the battery, start the car and put the car in reverse. The rear-view monitor should turn on and give you a view of what's behind you
Package Included:
1 x 7" TFT Screen Car Rear View Monitor
1 x Earphone
1 x Remote Controller
1 x Camera
1 x DC Power Cable
1 x Video Extension Cable(Optional)
1 x Hole Cutter/Drill
1 x User Manual
Shop for wholesale 7’’ LCD Car Rearview Mirror Monitor + 420 TVL CMOS Camera with cheap prices
