NEMA23 Stepper Motor *4 + Handle Remote Controller+ 4 AXIS TB6560 Stepper Driver + Power Supply l297

4 AXIS CNC Complete Kit - TB6560 Stepper Driver + NEMA23 Stepper Motor *4 + Handle Remote Controll + Power Supply

sku:UC139

4 Axis Stepper driver Features: 

 

• Toshiba TB6560AHQ chip - High power, maximum 3.5A drive current chipset !

• 1-1/16 ( 1/2,1/4,1/8,1/16 )microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!

• Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors

• Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !

• On board current switching - Power output can be set according to specific user requirement !

• Full closed-type optical isolation to protect the user's computer and equipment

• Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)

• 4 channel inputs interface- Can be used for XYZ limit and emergency stop !

• Professional design - Two stage signal processing with super anti-jamming !

• Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !

• Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !

• Universal architecture - Supports most parallel software MACH3,KCAM4 etc!

Dip settings:

Current Setting	1	2	Decay Mode Settings	3	4	MicroStep Settings	5	6
100%	ON	ON	FAST	ON	ON	1	ON	ON
75%	ON	OFF	25%	ON	OFF	1/2	ON	OFF
50%	OFF	ON	50%	OFF	ON	1/8	OFF	ON
25%	OFF	OFF	SLOW	OFF	OFF	1/16	OFF	OFF

 

Further Details:

• Power supply DC 12-36V (not included in this listing. Please feel free to check our other listings include power supply)

* This driver and the steppers get power from the same unit, they don't require separate power source.

* Voltage Selection:

12-16V DC power supply for Nema 17 stepper motors

16-24V DC power supply for Nema 23 stepper motors

24-36V DC power supply for Nema 34 stepper motors

Important: High voltage will burn up the chips or stepper motors!!!

* Ampertage Selection:

Output current of the power supply can be calculated by the following expressions:

Output current = Rated current of your stepper motors * quantity + 2A

For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.

If you are not sure about the selection of power supply, please feel free to contact us for help.

• The power output of 12V shall be applied to the radiator fan of 12V

• Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.

• Suitable for unipolar or bipolar stepper motors.

• Voltage regulated spindle speed controlled by parallel interface as function of supply voltage.

Data Sheet for 57BYGH56-401A Stepper Motor 

Model	Step angle	Motor length	Rated current	Phase resistance	Phase inductance	Holding torque		Lead wire	Weight
Single Shaft	°	L (mm)	A	Ω	mH	Oz-in	kgf.cm	No.	kg
57BYGH56-401A	1.8	56	2.8	0.9	2.5	175	12.6	4	0.7

 

 

This 57BYGH56-401A Stepper Motor is designed according to performance of TB6560AHQ driver board. They are the best match. If customer need other motor, please feel free to check following model data sheet.

  

Handle Instructions: 

1: The first drive with a corresponding docking connector board good driver board

2: turn on the power switch, power indicator light

3: Click the corresponding axis manual control buttons, the corresponding stepper motor shaft rotation axis while the corresponding indicator light, release the button to stop stepping motor

4: Manually adjust the speed dial number is about 300 degrees rotation within the (limited spaces on both sides of the fixed position), clockwise rotation acceleration, deceleration counterclockwise rotation.

 

Package contents

• 1 x TB6560 Stepper Motor Driver 1.5A-3A

• 6 x Wire connectors

• 1 x CD software(English Manual & Mach3 demo version)

• 1 x DB25 parallel cable

• 4 x Nema 23 57BYGH56-401A Stepper Motor

• 1 x DB25 parallel cable

• 1 x Handle remote control for 4 axis

• 1 x 24V Power Suply

   

Packaging Details

Unit Type: piece

Package Weight: 5.0kg (11.02lb.)

Package Size: 30cm x 30cm x 25cm (11.81in x 11.81in x 9.84in)

If you need to view, and save 4 AXIS CNC Complete Kit - TB6560 Stepper Driver + NEMA23 Stepper Motor *4 + Handle Remote Controll + Power Supply today and store crucial data for the future.

(bought amounts latest)

No one bought this product

Total records, divided into pages. First Prev Next Last

Goods Tag：

add tag