4 Axis CNC TB6560 Stepper Motor Driver Board + Handle Remote Controll

4 Axis CNC TB6560 Stepper Motor Driver Board + Handle Remote Controll

SKU:UC137

Stepper Motor Driver Specification:

Electrical properties (ambient temperature Tj = 25 C pm):
Input Power	12 - 36V DC power supply
Stepper motor drive current	1.5A - 3A/phase
Drive type	Double-pole constant flow PWM actuation output
Compatible Stepper motors	2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.
Dimensions	18 * 11 * 4 cm (L*W*H)

• 1-1/16 microstep setting - Higher accuracy and smoother operation than standard 1, 1/2 step!
• Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors
  *Attention: This driver is the 1.5A-3A version, it's specially designed for stepper motors with rated current from 1.5A to 3A, it's NOT compatible with stepper motors with rated current below 1.5A or above 3A!
  If the rated current your stepper motors is below 1.5A, you can choose the 0.5A-2.5A version!
  Please let us know which version (1.5A-3A version is default) you need immediately after placing a bid!
• Overload, over-current and over-temperature safety - Full protection for your computer and peripheral equipment !
• On board current switching - Power output can be set according to specific user requirement !
• Full closed-type optical isolation to protect the user's computer and equipment
• Relay spindle interface - Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
• 4 channel inputs interface- Can be used for XYZ limit and emergency stop !
• Professional design - Two stage signal processing with super anti-jamming !
• Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect !
• Four control inputs (divided into pairs of knives) - Allows setting of limit and emergency stop !
• Universal architecture - Supports most parallel software MACH3,KCAM4 etc!
  *For compatibility with other softwares, please feel free to contact us!   

Stepper Motor Driver Dip settings:

Current Setting	1	2	Decay Mode Settings	3	4	MicroStep Settings	5	6
100%	ON	ON	FAST	ON	ON	1	ON	ON
75%	ON	OFF	25%	ON	OFF	1/2	ON	OFF
50%	OFF	ON	50%	OFF	ON	1/8	OFF	ON
25%	OFF	OFF	SLOW	OFF	OFF	1/16	OFF	OFF

 Further Details:

 Power supply DC 12-36V (not included, please feel free to contact us if you need !)
*This driver get its power from the same unit as the steppers, it doesn't require a separate power source.

*Voltage Selection:
12-16V DC power supply for Nema 17 stepper motors
16-24V DC power supply for Nema 23 stepper motors
24-36V DC power supply for Nema 34 stepper motors
(High voltage will burn up the chips or stepper motors!!!)

*Ampertage Selection:
Output current of the power supply can be calculated by the following expressions:
Output current = Rated current of your stepper motors * quantity + 2A
 (For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good.
If you are not sure about the selection of power supply, please feel free to contact us for help)

The power output of 12V shall be applied to the radiator fan of 12V

Driver output compatible with 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max.

Suitable for unipolar or bipolar stepper motors.

Voltage regulated spindle speed controlled by parallel interface as function of supply voltage.

 

Handle Instructions:

1: The first drive with a corresponding docking connector board good driver board

2: turn on the power switch, power indicator light

3: Click the corresponding axis manual control buttons, the corresponding stepper motor shaft rotation axis while the corresponding indicator light, release the button to stop stepping motor

4: Manually adjust the speed dial number is about 300 degrees rotation within the (limited spaces on both sides of the fixed position), clockwise rotation acceleration, deceleration counterclockwise rotation. 

Package include: 

• 1 x 4 axis TB6560 Stepper Motor Driver 1.5A-3A
• 6 x Wire connectors
• 1 x DB25 parallel cable
• 1 x CD software(English Manual & Mach3 demo version) 
• 1 x Handle For 4 Axis
• 1 x Cable For Handle

Packaging Details

• Unit Type: piece
• Package Weight: 1.0kg (2.20lb.)
• Package Size: 26cm x 25cm x 18cm (10.24in x 9.84in x 7.09in)

   
     If you need to view, and save 4 Axis CNC TB6560 Stepper Motor Driver Board + Handle Remote Controll today and store crucial data for the future.

(bought amounts latest)

No one bought this product

Total records, divided into pages. First Prev Next Last

Goods Tag：

add tag

CNC 5 Axis Interface Board adapter for Stepper Motor Dr...

24V 14.6A 350W Single Output Switching Power Supply

TB6560AHQ - Stepper Motor Driver - microstepping - TB65...